Ajustable Treble Bass Frequency Divider 3 Way Speaker Audio Crossover Filters

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Ajustable Treble Bass Frequency Divider 3 Way Speaker Audio Crossover Filters
Popular
Popular
Product Introduction
Description
1.The crossover is suitable for a treble +mid +bass speakers. The speaker is suitable for 4-8 ohms. The finished products are also mostly used for better coordination. Sound quality, give debugging accessories at the same time of purchase.
2.The crossover is a popular finished product, which is connected to a variety of speakers. It is suitable for high and medium bass, and the sound quality is best; but not all speakers and all crossovers are the best fit. After use, there may be too much or too little treble, low frequency and low frequency of the bass, low frequency, or too thick bass, and too much or too little high frequency component in the midrange. It is.
3.No matter how good the parameters are, it is always the reference data. The sound quality is ultimately determined by the listener. Some people like to listen to treble. Some people like to listen to the bass, and some people like the midrange. Even if the parameters are very consistent, they match the different speakers. After that, the sound quality does not match the taste of the listener. People don't like this kind of sound, and there is no way to change it. When the frequency divider is connected, the next step of debugging is to solve the feeling of different requirements of each person, debugging and debugging, and the effect sound listener likes to use that sound. Refer to the instruction paper for the debugging procedure, and you can safely debug it, all within the scope of the speaker.
Treble debugging: 1: Just after the connection, there is no need to debug. 2: Change the mid-high frequency component of the treble. 3: Change the middle and high frequency components of the high pitch.
Midrange debugging: 1: Just after the connection, there is no need to debug. 2: Change the mid-high frequency component of the midrange to increase and decrease. 3: Change the mid-low frequency component of the midrange to increase or decrease.
Bass debugging: 1: Just after the connection, there is no need to debug. 2: Change the mid-low frequency component of the bass. 3: Change the low and medium frequency components of the bass to decrease.
Product parameters:
Frequency point: 950HZ/6000HZ (that is, the bass works at frequencies below 950HZ, the midrange works between 950HZ and 6000HZ, and the treble works above 6000HZ).
Power: 200W.
Impedance: 4-8 Ohm.
Circuit: Determined by debugging as 6db/oct to 12db/oct.
Material: Inductor adopts oxygen-free copper winding, pure copper wire diameter is thick, has been verified, 100% pure copper wire, will not use enameled aluminum wire production; capacitor uses audio dedicated electrodeless capacitor, fine materials but not Need more, reasonable design, beautiful appearance, excellent sound quality.
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Ajustable Treble Bass Frequency Divider 3 Way Speaker Audio Crossover Filters
Product Introduction
Description
1.The crossover is suitable for a treble +mid +bass speakers. The speaker is suitable for 4-8 ohms. The finished products are also mostly used for better coordination. Sound quality, give debugging accessories at the same time of purchase.
2.The crossover is a popular finished product, which is connected to a variety of speakers. It is suitable for high and medium bass, and the sound quality is best; but not all speakers and all crossovers are the best fit. After use, there may be too much or too little treble, low frequency and low frequency of the bass, low frequency, or too thick bass, and too much or too little high frequency component in the midrange. It is.
3.No matter how good the parameters are, it is always the reference data. The sound quality is ultimately determined by the listener. Some people like to listen to treble. Some people like to listen to the bass, and some people like the midrange. Even if the parameters are very consistent, they match the different speakers. After that, the sound quality does not match the taste of the listener. People don't like this kind of sound, and there is no way to change it. When the frequency divider is connected, the next step of debugging is to solve the feeling of different requirements of each person, debugging and debugging, and the effect sound listener likes to use that sound. Refer to the instruction paper for the debugging procedure, and you can safely debug it, all within the scope of the speaker.
Treble debugging: 1: Just after the connection, there is no need to debug. 2: Change the mid-high frequency component of the treble. 3: Change the middle and high frequency components of the high pitch.
Midrange debugging: 1: Just after the connection, there is no need to debug. 2: Change the mid-high frequency component of the midrange to increase and decrease. 3: Change the mid-low frequency component of the midrange to increase or decrease.
Bass debugging: 1: Just after the connection, there is no need to debug. 2: Change the mid-low frequency component of the bass. 3: Change the low and medium frequency components of the bass to decrease.
Product parameters:
Frequency point: 950HZ/6000HZ (that is, the bass works at frequencies below 950HZ, the midrange works between 950HZ and 6000HZ, and the treble works above 6000HZ).
Power: 200W.
Impedance: 4-8 Ohm.
Circuit: Determined by debugging as 6db/oct to 12db/oct.
Material: Inductor adopts oxygen-free copper winding, pure copper wire diameter is thick, has been verified, 100% pure copper wire, will not use enameled aluminum wire production; capacitor uses audio dedicated electrodeless capacitor, fine materials but not Need more, reasonable design, beautiful appearance, excellent sound quality.
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.